Upgrade Your Steam Deck OLED SSD with iFixit

Upgrading or replacing the SSD in your Steam Deck OLED is a simple process that can be done in about 30 minutes with the right tools and precautions. Upgrading the SSD in your Steam Deck OLED is an effective way to significantly increase storage capacity and performance. Following this quick guide from iFixit, from preparation to post-update steps, will ensure a smooth and successful SSD upgrade. Gather all the required tools ahead of time to make sure the process goes as smoothly as possible:

• Torx T6 screwdriver:This tool is necessary to remove the screws that secure the back cover of your Steam Deck OLED.
• iFixit Opening Choices:These picks will help you safely separate the back cover from the front casing without causing damage.
• Spudger:Spudger is a versatile tool that helps pry out various components during disassembly.
• Masking tape:When working with the device, you will need masking tape to securely fasten the cables.
• Tweezers:Tweezers are handy for precisely gripping small parts and components.
• Repair:Although optional, FixMat provides a convenient way to organize screws and components during the retrofit process.
• Replacement SSD drive:Of course, you’ll need the new SSD you plan to install in your Steam Deck OLED display.
• Protective film for SSD drive:The SSD protective film plays an important role in protecting your new SSD from electrostatic discharge (ESD) during installation.

Steam Deck OLED SSD Upgrade

Preparation: ensuring a smooth update

Before you begin the update process, be sure to take a few preparatory steps to ensure it goes smoothly and risk-free:

1. Back up your data: To prevent potential data loss during the update, please back up all important files and data from your Steam Deck OLED.

2. Discharge the battery: To minimize battery risks during the update, reduce the battery level on your device to less than 25%.

3. Activate battery storage mode:Activating battery storage mode allows for safe handling of the battery while working on your Steam Deck OLED.

4. Remove the MicroSD card: If there is a microSD card in your device, be sure to remove it to avoid any potential damage during the update process.

Disassembling the Steam Deck OLED Screen

Once you have completed the preparations, you can begin the disassembly process:

1. Remove Torx screws: Using a Torx T6 screwdriver, carefully remove the eight screws securing the back cover of the Steam Deck OLED display.

2. Separate the back cover: Carefully insert the pick between the back cover and front housing to separate them. Take your time and be careful not to damage any components.

3. Disconnect the battery cable: Carefully disconnect the battery cable to prevent any electrical hazards while working on the device.

4. Tape the connecting cable: Use masking tape to firmly isolate the connecting cable from the motherboard shield so that it does not interfere with the update process.

5. Remove the motherboard cover: Unscrew and carefully remove the motherboard cover to access the SSD.

Replacing the SSD drive

Once you have disassembled your device, you can proceed to replace the SSD:

1. Unscrew the SSD drive screw: Using a Torx T6 screwdriver, remove the screw securing the existing SSD.

2. ESD shield:If your new SSD does not have its own ESD shield, carefully transfer the shield from the old SSD to the new one.

3. Install a new SSD: Carefully insert the new SSD into the M.2 board connector, making sure it is properly aligned. Secure the SSD in place with the screw you removed earlier.

Reassembling the Steam Deck OLED

Once you have successfully replaced your SSD, it is time to reassemble the Steam Deck OLED display by following the removal steps in reverse order:

1. Reconnect the battery cable:Carefully reconnect the battery cable, making sure it is securely fastened.

2. Secure the motherboard cover: Reinstall the motherboard cover and secure it with the appropriate screws.

3. Reconnect the connecting cable: Remove the masking tape and reconnect the connecting cable, making sure it is properly seated.

4. Reinstalling the back cover: Align the back cover with the front cover and secure it with the eight Torx screws you removed earlier.

Steps after upgrade

Once you’ve completed the physical upgrade, there are a few final steps you need to take to ensure your Steam Deck OLED display is ready to use:

1. Install the operating system: Install the operating system on the new SSD by following the appropriate installation instructions.

2. Exit storage mode: Connect your Steam Deck OLED to a power source to exit battery storage mode and start using your device with an enhanced SSD.

By carefully following this step-by-step guide and taking the necessary precautions, you can successfully upgrade the SSD in your Steam Deck OLED, unlocking increased storage capacity and improved performance. Enjoy the benefits of your newly upgraded device!

Video Source: Source

Filed under: Gaming News, Breaking News

Geeky Gadgets Latest Deals

Disclosure: Some of our articles contain affiliate links. If you purchase something through one of these links, Geeky Gadgets may earn an affiliate commission. Learn more about our Disclosure Policy.